Can you have too much vented soffit?

You can't have too much soffit venting, but it's worth noting the minimum requirements. Usually, 4-in. by 16-in. soffit vents are rated for 26 sq.

finehomebuilding.com - Adequate Roof Venting - Fine Homebuilding

Are metal homes worth it?

Durability – A metal barn or shelter is far stronger than a wooden building. Metal buildings won't rot or warp over time, and they stand up to...

Last updated Feb 21, 2021

What holds nails better OSB or plywood?

Nails and screws are more likely to remain in place more firmly in plywood than in OSB. OSB retains water longer than plywood does, which makes...

Last updated Jul 21, 2021

Are shed plans easy to follow?

These are! They guide you every step of the way to complete your dream shed.

Learn More »

Promotion

Q:

I am having the shingles replaced on the roof of my ranch-style house. The roofer is concerned about attic ventilation and recommends installing a ridge vent and closing off the existing gable vents. He also says that the rectangular metal soffit vents may not be adequate and recommends installing more to eliminate the risk of the roof sheathing rotting. There are five vents in each soffit, and they measure about 4 in. by 16 in. each. Is it necessary to close off the gable vents? If so, how can I do that? Do I have to remove them and fill in the void with siding?

And how do I know how many soffit vents to install?

Mark Villar, Middletown, CT

A:

Editorial Adviser Mike Guertin replies: If the roof sheathing hasn’t begun to rot already, it’s unlikely that replacing the roof shingles will cause it to occur. Still, it’s a good idea to address ventilation to reduce attic heat in the summer and to reduce the chance for ice dams in the winter. Most likely, the roofer is recommending closing off the gable vents when adding a ridge vent to prevent short-circuiting of the air. When gable vents are left open, air can enter through the gables and bypass the soffit vents. If air flows in through the gables and out the ridge vents, the entire roof doesn’t receive the full effect. The air isn’t entering through the soffit vents, traveling up the underside of the roof, and exiting through the ridge vent. You don’t have to remove the gable vents, though. Just screw a piece of rigid foam or plywood over the vent from the inside. When the siding is replaced, the old gable vents can be removed and the openings filled. The standard equation for older homes that don’t have air barriers and vapor retarders (now required) is 1 sq. ft. of vent area for every 150 sq. ft. of attic floor. If your house is 26 ft. wide by 48 ft. long, you have a 1248-sq.-ft. attic floor and need 8.32 sq. ft. of total vent area. If, however, the attic floor has been air-sealed and has a vapor retarder between the inside of the house and the attic, the equation is 1 sq. ft. of vent area for every 300 sq. ft. of attic floor. Ideally, this 8.32-sq.-ft. total vent area is split: 4.16 sq. ft at the ridge and 4.16 sq. ft. at the soffits. Each type of vent has a range of effective vent area per linear foot—this is called the net free vent area (NFVA). Ridge-vent NFVA ranges from 14 sq. in. to 18 sq. in. per lin. ft. (Check manufacturers’ instructions for the ratings of specific products.) If 46 ft. of ridge vent (often it does not extend to the ends) is installed and the product has an NFVA of 15 sq. in. per lin. ft., we can take 46 ft. and multiply it by 15 sq. in., which equals 690 sq. in. Converted to square feet (690 divided by 144), the total is 4.8 sq. ft. This ridge vent supplies 4.8 sq. ft. of NFVA, which is just over half of 8.32 sq. ft.

How many plumbing vents should a house have?

At least one main vent stack is required for every building that has plumbing when connecting separately to the sewer for the building or its...

Last updated Jun 7, 2022

How do you grow plants in a shed?

Using your shed as a cover will be great. But make sure that your plants are near a sunny window so they can get light and warmth during the day....

Last updated Dec 28, 2018

Are shed plans easy to follow?

These are! They guide you every step of the way to complete your dream shed.

Learn More »

Promotion

You can’t have too much soffit venting, but it’s worth noting the minimum requirements. Usually, 4-in. by 16-in. soffit vents are rated for 26 sq. in. of NFVA each. With a total of 10 vents, you have a total of 260 sq. in. (1.8 sq. ft.) of soffit-vent area. Since you need at least 4.16 sq. ft. of NFVA, you’ll need to add 14 more of the 4-in. by 16-in. soffit vents (for a total of 4.3 sq. ft. of NFVA in the soffits). If the soffits are wide enough, you can remove the existing vents and replace them with 8-in. by 16-in. vents, which provide 65 sq. in. of NFVA per vent. With 10 of these large vents, you’ll end up with a more adequate 4.5 sq. ft. of NFVA in the soffits.

From Fine Homebuilding #257, pp. 80-81, January 6, 2016

finehomebuilding.com - Adequate Roof Venting - Fine Homebuilding

Why do Japanese people kneel when closing doors?

The skills of opening and closing a sliding Japanese door are a part of reishiki, "proper form," or "etiquette." The ability to move in a balanced...

Last updated Feb 20, 2019

How hard is it to buy a house in 2022?

Home buyers still face tough challenges in today's housing market: steep prices, elevated mortgage rates and a shortage of homes for sale. But the...

Last updated Dec 2, 2019

Promotion

What is the strongest type of roof?

About DECRA Metal Roofing If you're looking for the strongest type of roof, you're looking for a DECRA metal roof. Mar 28, 2022

Last updated Feb 3, 2020

Promotion

Are pavers stronger than concrete?

Whether you use cement pavers or want stone driveway paving, paving bricks and stones are typically stronger than concrete and can hold more weight...

Last updated Sep 17, 2020