Do you need a drill bit for Tapcon screws?

Carbide Tipped Drill Bits for Tapcon Screws Carbide tipped bit must be used for drilling the hole into the base material for the Tapcon screw. The quality ANSI standard carbide tips are brazed onto the end of the bit to ensure long life and consistent hole tolerance.

confast.com - Drill Bits for Tapcon - Concrete Fastening Systems

How can I heat my building without electricity?

15 Alternative Heat Sources for Power Outages to Keep You Comfortably Warm Indoor Kerosene Heater. Kerosene heaters can make great alternative heat...

Last updated Jan 11, 2019

Why are they banning Styrofoam?

Compounds in the foam are known carcinogens, the manufacturing process negatively affects workers and can contaminate neighborhoods, and the toxins...

Last updated Oct 31, 2018

Are shed plans easy to follow?

These are! They guide you every step of the way to complete your dream shed.

Learn More »

Promotion

Purchase Tapcon Anchors

Configuration

The flat end of the Tapcon drill bit is on the opposite end of the carbide tip and is the end of the bit that is inserted into the installation tool kit. This flat end of the Tapcon bit is aligned flat side out when inserted into the installation toolkit so that a set screw can be tightened against it, holding the Tapcon bit tightly in the installation tool.

Standards

Any carbide tipped masonry bit that is manufactured to meet ANSI standard B212-15-1994 can be used for drilling holes in masonry that Tapcon masonry anchors are installed in. If the installation toolkit is being used then the special Tapcon bit must be used.

Carbide Tipped Drill Bits for Tapcon Screws

Carbide tipped bit must be used for drilling the hole into the base material for the Tapcon screw. The quality ANSI standard carbide tips are brazed onto the end of the bit to ensure long life and consistent hole tolerance. Older style or less expensive carbide-tipped bits have the carbide soldered on. Solder has a lower melting point than the brazing method and will not last as long.

Diameters

The Tapcon drill bit that is used depends on the diameter of the Tapcon screw being installed. The 3/16” Tapcon requires the use of 5/32” diameter bit, and the 1/4” Tapcon requires a 3/16” diameter bit.

Length

The length of the Tapcon bit to use must be long enough to ensure that the hole drilled into the base material is 1/2” deeper than the Tapcon screw will penetrate the base material and will allow the Tapcon screw to meet minimum embedment depth of 1”. The designated length of each drill bit is measured as an overall length. The 5/32” Tapcon drill bit comes in three lengths and the 1/4” Tapcon drill bit comes in five lengths. The drilling depth of each length of the drill bit is 1-1/2” less than the overall length. Tapcon Diameter Diameter x Length Drill Depth 3/16” 5/32” x 3-1/2” 2” 5/32” x 4-1/2” 3” 5/32” x 5-1/2” 4” 1/4” 3/16” x 3-1/2” 2” 3/16” x 4-1/2” 3” 3/16” x 5-1/2” 4” 3/16” x 6-1/2” 5” 3/16” x 7-1/2 6” Each and every different length of Tapcon screw requires a specific length bit to be used to meet minimum hold depth requirements. The length of the bit is the same whether it’s a flat Phillips countersunk head or a hex washer head. The chart for each length of Tapcon and the correct corresponding bit that must be used is included below: Length of Tapcon Length of Tapcon Bit 1-1/4” 3-1/2” 1-3/4” 3-1/2” 2-1/4” 4-1/2” 2-3/4” 4-1/2” 3-1/4” 5-1/2” 3-3/4” 5-1/2” 4” 5-1/2” 5” 6-1/2” 6” 7-1/2”

What you Cannot put in a storage unit?

Storage units typically prohibit you from storing perishable items like meat, fish, cheese, and eggs. Avoid putting items that are illegal,...

Last updated Dec 29, 2019

What are the problems with metal sheds?

Condensation in metal sheds is a commonly reported problem The inside of the shed roof is running with water and this damp atmosphere is bad for...

Last updated Oct 20, 2021

Are shed plans easy to follow?

These are! They guide you every step of the way to complete your dream shed.

Learn More »

Promotion

Hammer Drill

The Tapcon drill bit must be used in a hammer drill, and the hammer drill must be set in the hammer and rotation mode. Hole tolerance is critical when installing Tapcon concrete screws. To produce the quality hole required, the Tapcon bit must be used in a rotary hammer drill. Unlike the standard rotary drill that requires the bit to cut the material to produce a hole, the hammer drill pulverizes the material with the hammering motion and the rotation removes the debris via the fluted section of the drill bit.

Other Drill Bits for Tapcons

There are other styles of bits that can be used for drilling holes in the base material for the Tapcon concrete screws. They must meet ANSI Standard B212-15-1994, be the correct diameter and length for the Tapcon being installed and must be used in a hammer drill that is set in the hammer and rotation mode. Straight Shank – the straight shank carbide tipped drill bits are designed for use in the Jacobs style chuck , one that requires a chuck key. These bits usually have a completely round shank or flat sides that fit into the chuck and are manufactured in many different diameters and lengths. , one that requires a chuck key. These bits usually have a completely round shank or flat sides that fit into the chuck and are manufactured in many different diameters and lengths. SDS – refers to spline drive system and are designed for use in hammer drills with a quick disconnect chuck. The shank of the SDS bit is about the size of a small finger with two slots and two groves. The slots are designed for positive rotation and the grooves allow the bit to move in the chuck allowing for a much harder hammering and thus creating a much faster drilling time.