Photo: Anna Shvets

Does heating plastic make it weaker?

productiveplastics.com - Temperature Considerations in Plastic Thermoforming Material Selection

What is a drawback of stone foundations?

Due to their composition and lack of uniformity, stone foundations are more likely to have problems when mortar crumbles due to water, bowing, or...

Last updated Aug 19, 2020

Can I make a shed livable?

Converting a shed into a house or living space is something that a lot of people have done and it's totally possible. They are a great way to have...

Last updated Feb 3, 2018

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

Temperature Considerations in Plastic Thermoforming Material Selection

If you’ve ever microwaved last night’s leftovers in the typical plastic to go container, you’ve witnessed the effect that high heat can have on thermoplastic. The plastic begins to soften and lose its stiffness as the material temperature increases and if you heat it long enough or exceed the limit of its operational temperature range, it will begin to distort. Worst case scenario, when you open the microwave door to enjoy your meal, you are presented with something that can be quite unrecognizable from what you put in. While this example may not be relevant in all cases, it does demonstrate the importance of selecting a plastic thermoforming material with the appropriate temperature properties for your application’s operating environment. Imagine a similar scenario on an essential safety, structural, or functional component for a medical, transportation, or industrial application. Loss of stiffness (flexural modulus) and material distortion (heat deflection) are just a few of the factors to account for when addressing the temperature requirements of a project.

Material considerations for prolonged exposure to excessive temperatures

Most of the effects of temperature to thermoplastic occur at high heat levels, although excessively low temperatures can have an impact as well. Mechanical properties, chemical resistance, electrical conductivity, material fatigue, and many other attributes can be affected by increased temperatures. Below is a list of the most common considerations. Note : The exact temperature thresholds and performance will vary for each different plastic material. In addition, factors like part geometry and material thickness will also affect material properties under extreme temperatures both high and low. The considerations below are just a general behavior characteristic of plastic in relation to temperature. (reference our article on material testing and data sheets for more information on standard testing of a material’s temperature performance)

Distortion

Exceeding a material’s approximate heat deflection temperature can cause the material to distort. Prolonged exposure to heat while subjected to a load or force can also cause plastic to deform or “creep” over time. Most thermoplastic materials have a heat distortion temperature (HDT) of less than 500 degrees F HDT is a good comparative specification of how different materials respond to the HDT test conditions but provides little information regarding the long term effects of continuous high temperature exposure on their physical, mechanical, thermal, and electrical properties.

Softening

Can I put a toilet in my garage without planning permission?

Nearly all internal works such as loft conversions, garage conversions, new staircases, bathrooms, kitchens, or rewiring, do not require planning...

Last updated Sep 27, 2018

Does my shed need a floor?

Shed floors are essential because they ensure a solid surface to walk on and sturdy support for items you store. If your items don't have a solid...

Last updated Apr 21, 2022

Promotion

As temperature increases, material stiffness (flexural modulus) will decrease.

Expansion

As with most materials, plastic expands as temperature increases (coefficient of thermal expansion – CTE). This can be a consideration when the plastic is mated with another material, such as metal, that may have conflicting thermal expansion rates. If the dimensional change is obstructed, stresses can be induced in the plastic part due to excessive tensile, shear, or compressive stress loads that could result in unexpected failure.

Service Life

Thermal Degradation – Plastic materials subjected to prolonged exposure to high temperatures will lose strength and toughness, becoming more prone to cracking, chipping, and breaking, at a rate in proportion to the temperature and time of exposure. Materials exposed to higher heat for longer duration will wear substantially faster than those exposed to more moderate temperatures and exposure times. The Continuous Use Temperature Rating is based on a thermal aging test that predicts the temperature at which a 50% loss of the original mechanical properties will occur after 100,000 hours of continuous exposure at that temperature. (see table below)

Thermal Conductivity

The quantity of heat that passes through a cube of the material in a certain period of time when the difference in temperature between the two surfaces becomes one degree. Plastic materials generally have a much lower Thermal Conductivity than metals. This makes them excellent replacement materials when thermal insulation is important. Some questions to consider to determine your application’s temperature profile and ideal material candidates During the product development process, Productive Plastics uses the following questions to zero in on the plastic material options that will be temperature compatible for a customer’s application:

What environmental temperature range (high and low) will the part be exposed to operationally? What dimensional and stiffness (flexural modulus) tolerances are required of the part at the high, mid, and low points of its expected temperature range? What loads or forces are expected on the part at the high end of its temperature range? What is the time/temperature relationship? A low temperature for a long time can result in comparable properties damage as a high temperature for a short time. What is the projected service life of the application? Will the plastic part be mated to any other material types, such as metal, as part of the application design? What are the specified (FST) flame, smoke & toxicity requirements?

Available thermoplastic options and temperature performance

Can I build a lean-to shed without planning permission?

Permitted Development rules For example, you can add an extension, porch or lean to without planning permission as long as: It is within the...

Last updated Jul 25, 2019

What are 10 good insulators?

10 Electrical Insulators Rubber. Glass. Pure water. Oil. Air. Diamond. Dry wood. Dry cotton. More items... • Nov 24, 2019

Last updated Feb 4, 2018

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

As discussed in previous posts on material selection, when it comes to plastic material options, there are many choices and each has different thermal and mechanical performance properties. The information below will give you a general understanding of the operating thermal ranges of the common plastic material options available. Note: The options listed are generic plastic material formulations. Many plastic material companies have specific plastic material products formulated and designed to meet the demands of a wide range of industry requirements. For information on the thermal performance of these products, visit our material supplier datasheet page or our thermofoming materials page. Productive Plastics is top contract manufacturer for heavy gauge thermoforming, including vacuum forming and pressure forming. Contact us or request our complimentary thermoforming design guide for more information.

productiveplastics.com - Temperature Considerations in Plastic Thermoforming Material Selection

How do you finish a shed roof?

How to Finish the Top Edge of a Shed Roof For the final row, cut shingles into strips. Ensure strips are wide enough to cover nails. Install your...

Last updated Mar 19, 2021

What can I put around my shed?

You can plant flowers, shrubs, small-growing evergreen bushes, vegetables, or herbs in front of your shed. Typically, most people plant either...

Last updated Dec 21, 2020

Promotion

What is the easiest thing to make and sell?

13 Easy Things To Make and Sell Sweet Treats. Cookies and candies and cakes, oh my! ... T-shirts. If you're not exceptionally creative, t-shirts...

Last updated Jun 1, 2022

Promotion

What happens to an IRA when someone dies?

Beneficiaries of retirement plan and IRA accounts after the death of the account owner are subject to required minimum distribution (RMD) rules. A...

Last updated Jun 23, 2018