Does shed floor need joist hangers?

The best shed-floor framing is simple and sturdy If the joists are set atop a plate (see picture) then you won't need joist hangers to reinforce the ends of each joist. If no plates are used, you must use joist hangers.

finehomebuilding.com - Building a Shed? Get the Site, Footings, and Floor Frame Right

What is ripping in woodwork?

Ripping refers to cutting the wood along its grain for a lengthwise cut. This type of cut is easy to make, especially when your table saw is...

Last updated May 23, 2022

What is the best base for a metal shed?

We recommend using paving slabs, tarmac or concrete. A solid concrete base is more permanent and provides an excellent base for a metal shed....

Last updated Feb 22, 2020

Promotion

You may never look at it again, but one of the most important parts of a shed structure is the floor frame. Not only will the building method change depending on your overall design, but it’s also important to think about moisture, load paths, lumber spans, and the basics of proper framing.

Start with a solid base

Unless you live in an area that’s so dry that moisture accumulation isn’t a concern, or have soil that drains exceedingly well, it’s a good idea to cover the area under the shed with several inches of coarse gravel (3/4″ is a common option). The idea behind the coarse gravel is that it defeats the natural process of capillarity, which causes water to rise up from the ground after rainfall. Forgive my simplistic builder’s summary of capillarity, but it’s essentially a function that allows water to be sucked from large areas to smaller areas, regardless of gravity. The spaces between pieces of gravel are essentially large pores, and are large compared to the smaller pores between grains of soil, sand, or whatever substrate is below the gravel. So, by adding a layer of gravel, you’ve eliminated the ability of water to wick upward into your shed. Gravel also aids drainage and evaporation, both of which are crucial under a shed. You can’t always stop water, but you can provide it a means for running off or drying. If you lay a bed of gravel you can actually build the shed floor frame right on the gravel. This is a common approach when buying a factory-built shed. You’ll want to check with your local building department to make sure they’re ok with this (most I’ve encountered consider small detached structures under a certain square footage to not require permanent footings). Another common approach is to set concrete blocks on the ground, first digging out the grass and topsoil, to a depth of maybe 6 or 12 inches below grade, and fill the hole with gravel. Use solid concrete blocks, not the hollow variety used in masonry wall construction, and remember that blocks are commonly available in several sizes, which is handy when it comes to getting close to level. As a rule I don’t stack blocks more than 2 or 3 high (depending on block size) because the higher the stack the lower the stability. In situations where the ground is sloping severely, or you want a more permanent connection with the site, you should choose poured concrete footings that extend below the local frost depth. If the shed will be on stacked blocks or poured footings you’ll need to consider the number of footings and how they are spaced. This is directly tied to the type of floor frame you will be using.

The best shed-floor framing is simple and sturdy

How much lumber is needed for a 12x16 shed?

standard sizes of 96” x 48”, you'll need about 496SF to cover the entire shed. For the front wall siding, measure and cut out the door and window...

Last updated Aug 23, 2019

How do I stop damp in my brick shed?

Use a liquid damp-proof membrane or tanking slurry, which if applied correctly would prevent damp from reaching the internal side of the concrete...

Last updated Nov 10, 2021

Promotion

In most cases a shed is built atop a floor frame of dimensional lumber and plywood or OSB. This method is fast, and follows conventional and familiar framing techniques. Joists run the short direction, typically spaced every 16 inches, and are captured by rim joists on the long sides of the shed. If the joists are set atop a plate (see picture) then you won’t need joist hangers to reinforce the ends of each joist. If no plates are used, you must use joist hangers. Also, pay attention to the span of the lumber you’re choosing for the floor, information which can be found readily on the internet, in building code books, or at your local building department. Often people will oversize their joists, thinking that 2x10s “look” right for a floor frame, when in reality 2x6s or 2x8s might be more than adequate and can save money. Don’t forget to use galvanized nails for constructing this portion of the shed frame! Standard (“bright”) framing nails are not compatible with pressure-treated lumber!

Happy building!

– Justin

Follow editorial director Justin Fink on Instagram @mrjfink

finehomebuilding.com - Building a Shed? Get the Site, Footings, and Floor Frame Right

Does garage slab need to be lower than house?

Floor Level Old habits die hard. Building codes used to stipulate that the floor of an attached garage be four inches lower than the floor level of...

Last updated Jun 20, 2020

How can I heat my small shed without electricity?

How to Heat a Shed Without Electricity: 10 Practical Ideas and... Make Sure It's Well Insulated. Let Some Sunlight In. Build A Solar Window Heater....

Last updated Jun 21, 2018