Does wiring in a garage need to be in conduit?

Many garages contain one or more walls made of concrete or already drywalled. Cable installed on these exposed surfaces has to be protected by conduit. We show EMT (electrical metallic tubing; Photo 7), but you can also use rigid PVC conduit.

familyhandyman.com - How to Wire a Garage (Unfinished) (DIY) - The Family Handyman

Is there wood in toothpaste?

Wood in Toothpaste A form of cellulose known as cellulose gum, or Sodium Carboxymethyl Cellulose (CMC), plays several roles in toothpaste: thanks...

Last updated Aug 20, 2020

Do horse barns add value to property?

Not only will you be able to use that storage for your own needs, but chances are good that if you go to sell your property, this will be an...

Last updated Jun 9, 2018

Promotion

How to Wire a Garage (Unfinished)

How to add outlets and lights to an unfinished garage.

Family Handyman Frustrated by too few outlets in your garage? Lighting that's too dim? Or maybe you just want to install a garage door opener and need a nearby plug-in. If so, this article is for you. Garage wiring has special rules. So before installing those extra outlets, read through the details in this story to make sure that you're doing it safely and according to the Electrical Code. You might also like: TBD Time A full day Complexity Intermediate Cost $51–100

Basic wiring strategy for garages

Wiring an unfinished garage. Wire your unfinished garage to get the lights and outlets you need. Whether you’re rewiring or adding more wiring to an older garage, or running wires in a new garage, you have a decision to make. Do you plan to leave the walls open or close them up with drywall? If you intend to leave the walls and ceiling open, you have to follow the special rules that we show here. The same goes for sheds, workshops or other structures with unfinished walls outside the living space of the house. In a house or a finished garage, electrical cable is protected from damage by permanent wallcoverings like drywall, plaster or even wood, but that’s not the case in an unfinished garage. The key to safe, code-compliant exposed wiring is to use the framing members to protect and support the wires. That means not spanning stud or joist spaces with wires. Keep all the cables closely hugging the studs, plates and ceiling joists so they’re not subject to abuse (see “Dangerous Wiring Mistakes” at the end of this article). In this story, we’ll show you a common, cost effective and code approved way to run exposed electrical cable. But there’s one downside to this method: If you ever do decide to finish the area, you’ll have to completely rewire because the surface-mounted cables will make drywalling impossible. In an unfinished garage, the trick is to follow the framing. Instead of connecting switch, light and outlet boxes by spanning framing spaces, route cable along studs, top plates and ceiling joists (Photo 3), along whichever framing member leads to the next box (see lead photo). That means you’ll use a lot more cable, because the paths are rarely direct. But cable’s cheap and quick to run. Keep all cables exposed and easy to see and never run cables on the tops of walls; keep them on vertical surfaces. That way the wires won’t ever have anything resting on them like hooks or garden tools (Photo 6).

Set the boxes and run the wires

Can you make a living off of woodworking?

1- Can you make a living off woodworking? The short answer is 'yes', but there are some caveats. Just go on YouTube and you'll see that there are...

Last updated Sep 14, 2022

What is the best size for a garage?

An averagely sized garage is 22′ to 24′. If your car's width is 6′ to 6.5′, adding a few feet all around will give you 20′, which is the minimum...

Last updated Jun 4, 2020

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

Photo 1: Insert the wires in the box Strip at least 8 in. of the plastic sheathing off one end of the cable and thread the wires through the electrical box cable entrance. Make sure that about 1/2 in. of the plastic sheathing at the base of the exposed wires projects inside the box Staple the cable within 8 in. of the box. Space cables at least 1-1/4 in. from the front and back of framing members. Photo 2: Drill holes to run cable Run cable alongside and centered on studs, drilling holes through blocking as close to the framing as possible to continue cable runs Photo 3: Bend cables around corners Bend cable tightly around corners at transitions and staple near the bends to contain the cable. Photo 4: Staple cable near boxes Staple within 12 in. of boxes that have built-in cable clamps. Stacker staples allow for stacking cables in the center of studs. Photo 5: Run cable along the sides of braces Run cable across ceiling joists by using the sides (not the top) of existing braces. This can shorten some cable runs. Photo 6: Run cable along the gable ends. Run cable along the bottom faces of gable end framing but never lay it atop wall plates where it can’t be seen. If you run cable along the face of plates, don’t hang tools there Begin by planning your wiring scheme and nailing up all the electrical boxes. To run a cable from one box to another, pull cable off the coil, strip at least 8 in. of sheathing off the wires and thread the wires and about 1/2 in. of sheathing through the wire opening in the box. Untwist the cable and staple it at least every 4 ft. to the framing, all the way to the next box without cutting it to length. When you reach the next box, stretch out the cable and mark the entrance point on the cable, cut the cable about a foot long, strip the sheathing and feed the wires into the box. Then nail in the staples near the box. The code requires that you hold all wires at least 1-1/4 in. (Photo 1) from the back and front surface of studs and joists. With 2×4 framing, that means you have to hold two cables running side by side tight to each other. If you’re running three or more cables, you’ll need special “stacker” staples (Photo 4) so you can piggyback cables on top of one another. Stacker staples aren’t always sold at home centers, but you can find them at electrical supply stores. Sometimes these staples are the only option because of the number of wires in a stud space. Cable should be stapled at least every 48 in. between boxes, but as rule, the more staples the better. Avoid sagging cables and keep turns tight by using as many staples as necessary. Electrical boxes may have built-in metal or plastic cable clamps. Many duplex boxes only have knockouts. Cable should be stapled within 8 in. of boxes without clamps and within 12 in. of boxes with clamps (Photo 4).

Do you need to put a base down for a shed?

Typically, any shed larger than 6×8 or 8×8 is going to require a foundation. However, a foundation is a good idea even for small sheds, because the...

Last updated Feb 24, 2022

Why would a house not have gutters?

Some homes — homes with particular qualities — do not need gutters. A home with no basement or a home with excellent landscaping drainage may not...

Last updated Sep 16, 2019

Are shed plans easy to follow?

These are! They guide you every step of the way to complete your dream shed.

Learn More »

Promotion

How to run surface wiring on solid walls

Photo 7: Protect cables on hard walls with conduit. Protect surface cables on hard-surfaced walls by encasing them in either PVC or metal conduit. Use connectors and boxes and straps that are compatible with each type of conduit. When running cable out an open conduit end, be sure to use a connector fitting. Many garages contain one or more walls made of concrete or already drywalled. Cable installed on these exposed surfaces has to be protected by conduit. We show EMT (electrical metallic tubing; Photo 7), but you can also use rigid PVC conduit. Use 1/2-in. tubing for one cable (14-2 or 12-2) and 3/4-in. for two cables. Whichever conduit style you use, choose boxes, straps and connectors that are specifically made for that type of conduit. Screw boxes to walls through the back into solid backing and use straps at least every 4 ft. to fasten the conduit to the wall. Route conduit until you reach the open stud spaces and then continue wiring as we’ve described. Never exit wires through cut ends of conduit because the sharp metal edges can cut into the sheathing. Always exit cable through connectors. Dangerous Wiring Mistakes Avoid running cables like we show in the photos below. Cables that span stud spaces or ceiling joists are in constant jeopardy of nicks or cuts from sharp shovels, opening car doors or nearly anything else you’ll find in a garage. As if that’s not bad enough, it’s too tempting to use them for tucking, hanging or trapping all kinds of paraphernalia to get it off the floor and out of the way.

Required Tools for this Project

Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.

4-in-1 screwdriver

Drill/driver - cordless

Hammer

Wire stripper/cutter

Required Materials for this Project

Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.

familyhandyman.com - How to Wire a Garage (Unfinished) (DIY) - The Family Handyman

Do I need to vent my greenhouse?

Your greenhouse needs vents to allow fresh air to move in, but you should also have some kind of circulation fan to keep the air moving throughout...

Last updated Aug 9, 2018

What should I charge for handmade items?

In her Tips for Pricing your Handmade Goods blog on Craftsy, artesian entrepreneur Ashley Martineau suggests this formula: Cost of supplies + $10...

Last updated Feb 7, 2021

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

What is the shallowest roof pitch?

Defining low pitch Traditionally, a minimum pitch of 20° was recommended, modern roofing products have made it possible to create equally...

Last updated May 17, 2020

Promotion

How small can a studio be?

A micro apartment is typically between 100-400 square feet. In a 300-square-foot micro apartment, roughly 60 square feet will be kitchen area, and...

Last updated Sep 30, 2020