How do you run electricity to a detached garage?

To build your garage subpanel, dig a 20-inch deep trench for the outdoor electrical wire, which you will run from the main panel box to the garage sub panel: Use 1 1/4-inch PVC conduit for a 100-amp sub panel or 1-inch PVC conduit if the sub panel is 50 amps or less.

hunker.com - How to Run a Subpanel to a Detached Garage | Hunker

What furniture is most important?

The most important pieces of furniture for your home Chest of Drawers. Boookcase. Armchair. Dining room table. Desk. Wardrobe. Bed. Outdoor table....

Last updated Nov 15, 2022

Is 600 sq ft a tiny house?

Tiny homes are generally designated as being under 600 square feet, but the average size of a tiny house for sale in the U.S. is actually just 225...

Last updated Jun 4, 2022

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

Installing a sub panel — another name for a breaker box — in a detached garage makes it convenient to turn the electricity off and on when needed. (Because who wants to go all the way down to the basement when you need to shut the power off in the garage?)

Video of the Day

When installing a sub panel in a detached garage, the first thing to think about is the size of voltage you'll need. This depends on how much power you typically use when working in your garage. If you are running welders and compressors that require high voltage then you will need a 100-amp sub panel. If you are just doing small jobs then you will only need a 50- to 60-amp sub panel.

Here's a step-by-step guide to running a subpanel to a detached garage.

Tip If you are unfamiliar with electrical systems, it's best to have a professional electrician handle this job so you don't injure yourself or damage your home.

1. Prepare for the Job

If you do not have (and will never have) a phone cable, gas line, water lines, computer cable, or TV cable in the garage, you only need to run a red, black, and white wire from the house. The sub-panel can be grounded at the garage. Before you build the subpanel, you'll need to install a 6-foot ground rod outside the garage and run a ground wire from the sub-panel box to the ground rod. The ground wire does not have to be in a conduit. Warning Remember, you're working with electricity, so follow good safety procedures. The National Electrical Code (NEC) requires the installation of ground fault circuit interrupters (GFCI ) for any outside wiring. Use rubber insulated gloves when working with electricity. Never work in the panel box when it is “Live.” If you do not use a GFCI breaker or receptacle outside you could get seriously shocked and start a fire.

2. Build Your Garage Sub Panel

To build your garage subpanel, dig a 20-inch deep trench for the outdoor electrical wire, which you will run from the main panel box to the garage sub panel: Use 1 1/4-inch PVC conduit for a 100-amp sub panel or 1-inch PVC conduit if the sub panel is 50 amps or less.

Run the conduit from the garage to the main panel box.

What size of pipe do you need to move a shed?

The first thing you want to do is make sure you have the necessary tools and parts to get the job done: Floor jack (two will make it even easier) 8...

Last updated Jul 14, 2018

What is considered a permanent foundation for a shed?

A “permanent foundation” is the kind that can not be removed or dismantled easily. It's usually a concrete slab or concrete piers. However,...

Last updated May 23, 2020

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

If concrete has not been poured in the garage, run conduit down into the ground on the inside of the garage. Use a 90-degree sweep connector, instead of a sharp 90-degree connector, to make it easier to pull the wire through. If the concrete is already done, run the conduit up the wall on the outside of the garage and use a PVC LB access fitting to go through the wall where the sub panel box is to be mounted. Do the same at the main panel box. Screw a piece of plywood that is 6 inches bigger than the sub panel to the wall where the sub panel will be mounted. This is called a backer. Screw the sub panel box to the center of the backer and connect the conduit to the sub panel. Some local codes require the backer to be painted black. Use #8 THHN wire for a 50-amp sub-panel or #2 THHN wire if the sub-panel is 100 amps.

Run the wire from the main panel to the sub-panel box.

Run black, red, white and green wires from the sub-panel box to the main panel box. Tip If the weather is cold outside, keep the wire inside to keep it warm. The wire will be easier to work with if it is not cold.

3. Make the Connections

Now you'll need to make the proper connections to finish the job:

In the sub panel, connect the red and black wires to the main breaker on the sub panel. Connect the white wire to the neutral bus bar, located along the side of the main bus, and connect the green wire to the ground bus bar, which is connected directly onto the sub-panel. In the main panel box, install the breaker into the main bus. Connect the red and black wires to the screws on the breaker. Connect the white wire to the neutral bus bar and the green wire to the ground bus bar. Test the sub-panel with a voltage meter to ensure it has the correct amperage.