How do you secure a curb ramp?

Bolt Together Your Curb Ramps Just use metal nuts and bolts to attach the ramps to each other. The combined weight will help prevent your curb ramps from sliding around. BRIDJIT curb ramps are designed to be bolted together. When bolted together, a set of BRIDJIT curb ramp weighs at least 153 pounds.

bridjit.com - How To Keep Your Curb Ramps From Moving

How much gravel should I put under concrete?

How Much Gravel Do You Put Under a Concrete Slab? You will need 3 inches of gravel under a concrete slab that is 4 inches thick. More gravel is...

Last updated May 1, 2019

How do you attach wood to concrete without drilling?

Fastening wood to concrete without drilling can be done using a variety of different construction adhesives, or using a hammer and either cut or...

Last updated Aug 14, 2021

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

It can be annoying when your curb ramps slide around instead of staying put. A curb ramp that’s not in place will create another bump to cross instead of smoothing out the entry to the driveway. Also, you would have to get out of your car and readjust the curb ramps every time you need to use them. You may be tempted to bolt your curb ramp into the concrete curb, but it’s a terrible idea. The good news is that there are much more effective ways to make sure that your curb ramps stay put.

1. Clean Under Your Ramps Every Several Months

Did you know that dirt and debris can cause your curb ramps to move around? It’s common for dirt and sand to accumulate under curb ramps over time. This reduces the traction between the ramps and the curb. It’s because: When combined with water, dirt and debris can turn into sludge. This acts as a lubricant. Some types of debris, such as sand or gravel, can act as ball bearings. They’ll help your curb ramps slide around instead of staying put. To prevent this from happening, clean under your curb ramps every few months or so. BRIDJIT curb ramps are pretty easy to hose down. It’s because they’re made of recycled rubber. You can find instructions here.

2. Bolt Together Your Curb Ramps

The more your curb ramps weigh, the less likely they’ll move around. One way to do this is by bolting your curb ramps together. Just use metal nuts and bolts to attach the ramps to each other. The combined weight will help prevent your curb ramps from sliding around. BRIDJIT curb ramps are designed to be bolted together. When bolted together, a set of BRIDJIT curb ramp weighs at least 153 pounds. This really helps with ensuring that your curb ramps stay put. Every BRIDJIT curb ramp set comes with ½” x 7.5” galvanized bolts. These bolts are pre-inserted in the center sections. You’ll also get a set of detailed instructions on how to bolt these ramp sections together.

3. Pull In And Out The Same Way Each Time

Whats a farmers porch?

Farmers Porch: A farmer's porch (sometimes referred to as an open porch) is a style that is traditional to old New England homes. These open-air...

Last updated May 22, 2019

What's the hardest wood?

1. Australian Buloke – 5,060 IBF. An ironwood tree that is native to Australia, this wood comes from a species of tree occurring across most of...

Last updated Feb 5, 2018

Promotion

This one is easy if you have space on your street and practice it as a habit. Don’t enter the driveway at an angle. If you can swing out in the street and enter with both tires impacting the ramps at the same time, the ramps will stay put.

4. Create An Anchor

While BRIDJIT curb ramps tend to stay put better than other brands, some BRIDJIT curb ramp owners have had success for a more permanent solution. They have created an anchor of sorts. If you are fortunate to have a control joint in the right place in your curb, you may want to try this method: After completing your BRIDJIT curb ramp setup, match the position of the ramp’s bolted connections to the joint . . Measure to be sure you are placing it slightly above where the top connection bolt will rest, then insert a 3 ½ in outside-diameter galvanized washer* down through the rubber joint and into the concrete joint. Pound the washer into the joint until it is flush with the rubber seam. Make sure you are placing the second washer slightly below where the ramp’s bottom connection bolt will rest, then insert the second 3 ½ in outside-diameter washer down through the rubber joint and into the concrete joint. Pound the washer into the joint until it is flush with the rubber seam. This creates a sheer point that keeps the entire ramp in place and still allows you to pull the top of the ramp out into the street for cleaning. Remember, this setup only works if you have a control joint in the right place with enough opening in the joint for the washer to be inserted, but it is amazing how many times this actually works. *This 3 ½-inch size washer cannot be purchased at the go-to hardware stores. You will need to Google “fasteners” to find them here. If you have all the right components, this method will help keep your ramps from moving.

bridjit.com - How To Keep Your Curb Ramps From Moving

Can copper pipe be used as A grounding rod?

For installations with a longer service life, copper-bonded ground rods are the best fit. For many years, the copper cold water pipe has served as...

Last updated Jan 3, 2020

What is the least expensive roof to build?

Generally, a gable-style roof with asphalt roofing shingles is one of the most affordable roofs you can build on a residential home. Asphalt...

Last updated Aug 7, 2021

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

Where should I put a shed in my garden?

Sheds that are going to be frequently used will be best placed near to the home, whereas if you are going to be storing heavy duty items such as a...

Last updated Aug 8, 2021

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

What is the minimum area required to build a house?

According to this standard, the minimum floor area for any new home should be 37 sq. m. [2] Where a one person flat has a shower room rather than a...

Last updated Aug 12, 2022