Photo: Brett Sayles

How far apart are studs?

The general spacing for wall studs is 16 inches on center, but they can be 24 inches. At my home, the exterior wall studs are spaced at 24-inch centers, but the interior walls are 16 inches on center.

washingtonpost.com - How to find studs hidden inside walls - The Washington Post

Can I use sand instead of sub-base?

As a general rule, stay away from using sand as a subbase. You're better off using gravel; your concrete will last longer and have less of a chance...

Last updated Jan 23, 2021

How far apart should 2x4 be in a shed wall?

There are two stud spacing options for a shed: 16-inch and 24-inch stud spacing. Studs spaced at 16-inches make for a sturdier shed, but the...

Last updated Jun 9, 2022

Promotion

I need to hang some cabinets, but I don’t own an expensive stud-finder tool. In the past, when I’ve borrowed one I had limited success using it. Can you share any secrets on how to find wall studs or ceiling joists hidden behind drywall or plaster without one? And how do I prevent making the walls look like a woodpecker was here?

—Ed R., Warwick, R.I.

I hear your lamentations about the electronic stud finders. They are great tools in certain situations, but sometimes they can be really frustrating. Two years ago, I was using a stud finder and it was giving all sorts of false positive signals. It would indicate where a ceiling joist was behind drywall, and when you drove a nail, the joist wasn’t there. I even had the house plans and knew the direction of the floor joists. It turned out that the device was finding them, but that they were recessed from the inside surface of the drywall by 3 / 4 of an inch. The builder’s rough carpenters had installed 1-by-3 furring strips across the entire ceiling at 90-degree angles to the floor joists. You can see why using these tools requires a knowledge of building habits in certain parts of the nation. Just last weekend, I had to find some wall studs to hang wall cabinets. I reverted to my old-fashioned method of a hammer and a nail. It works well, and because I carefully picked the spots where I drove the nails, the cabinets covered the exploratory holes after they were hung. The first thing I do when I have to find a stud is to look for clues as to where they would be. If the house is built after about 1950, I look for electrical wall outlets. In almost all situations, the boxes that house the outlets are nailed to the side of a wall stud. In rare instances, a wall outlet may have been added at a later date, but in these situations a special remodeling box is used that doesn’t need to be nailed to a wall stud. I also look for poorly patched nail holes in baseboard. This is less accurate because in some places, rough carpenters install a double-bottom wall plate. This allows them to randomly nail baseboard trim to the bottom plates instead of a vertical wall stud.

What is a fast growing plant for screening?

Fast-growing screening trees and shrubs Photinia Robusta is a popular hedge plant that's great for screening off your front yard. New foliage grows...

Last updated Jun 7, 2018

Can a solar panel run a heater?

The electricity produced by solar panels can be used for any home appliance, not only heat pumps or resistance heaters. Feb 24, 2021

Last updated Jun 19, 2022

Promotion

You can also look on a wall for a return air duct if the house has central air conditioning or forced-air heat. Wall registers are commonly put between two wall studs. Remove a return-air grill covering, and you’ll almost always see two wall studs. The general spacing for wall studs is 16 inches on center, but they can be 24 inches. At my home, the exterior wall studs are spaced at 24-inch centers, but the interior walls are 16 inches on center. However, just because you find one wall stud, that doesn’t mean you can say that every other stud on the wall is 16 inches on center from that one. Rough lumber can bow and twist. It’s possible for the spacing to be off by as much as 1 inch or more either direction, especially halfway between the floor and ceiling, where studs tend to bow the most. I use a 10d finish nail to find wall studs. These create tiny holes that are easily patched with spackling compound. My technique is to find at least one part of the wall stud and then drive nearby holes that tell me where the edges of the stud are. Once I find the edges, considering that most studs are 1.5 inches wide, I then know where the center of it is.

— Tribune Media

Tim Carter is a columnist for Tribune Media Services. He can be contacted through his Web site, askthebuilder.com.

washingtonpost.com - How to find studs hidden inside walls - The Washington Post

What is it called when you own the house but not the land?

Under a ground lease, tenants own their building, but not the land it's built on. Since this is a lesser-known type of leasing structure, here's a...

Last updated Dec 4, 2019

Should your barn match your house?

Barns and buildings, however, do not have to match the house, with the prime example being a red barn next to a classic white farmhouse. Similarly,...

Last updated Mar 31, 2020

Are shed plans easy to follow?

These are! They guide you every step of the way to complete your dream shed.

Learn More »

Promotion

Does a shed floor need ventilation?

Effective ventilation prevents excess moisture build-up, which if not tackled, might lead to mildew and mold growth. Your shed must have a good...

Last updated Jan 7, 2020

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

How thick should backyard gravel be?

Lay the groundwork Landscape fabric also tends to show up at the surface. Instead, lay a 2- to 3-inch-thick layer of gravel directly on bare, weed-...

Last updated Jan 10, 2022