Photo: Jorge Medina

How tight should insulation be packed?

Fill gaps around windows and doors wide putty knife. The insulation should fit snugly, but don't pack it.

familyhandyman.com - How to Install Fiberglass Batt Insulation - The Family Handyman

Can Neighbour build garage without planning?

Outbuildings such as sheds, garages, greenhouses and some other structures like garden rooms are also considered to fall within permitted...

Last updated Aug 28, 2018

Can you pour concrete under water?

The good news is that you can pour the concrete in water. Professionals do this all the time. You just have a small standing puddle in your...

Last updated Jul 29, 2020

These are the Best Shed Plans!

Comprehensive and Intuitive to follow. Build That Shed!

Learn More »

Promotion

How to Install Fiberglass Batt Insulation

You've only got one chance to do it right! Here's how

Family Handyman Fiberglass batts are the cheapest, easiest way to insulate new walls. However, they're often installed poorly—and even small gaps can reduce efficiency as much as 25 percent. In this article, we'll show you how to avoid those mistakes, how to cut and fit fiberglass batts and how to work around electrical outlets and cables. You might also like: TBD Time A full day Complexity Beginner Cost Varies

Fill all voids

Fill the stud cavity Push batts all the way to the back of each stud space and then pull out the front edges until they’re flush with the face of the studs. The key to a quality insulating job is tight-fitting batts that completely fill the stud cavity with no voids or gaps. You can do top-quality work with only a few basic tools. You’ll need a utility knife with a good supply of sharp blades, a tape measure and a straightedge, and a 3- or 4-in. putty knife for stuffing insulation around doors and windows. Fiberglass can irritate your throat and skin, so wear protective gear. Buy a two-strap mask rated for fiberglass insulation (look for N-95 rating) and wear a hat, gloves, a long-sleeve shirt and goggles to keep fibers out of your eyes.

Fit batts tightly around electrical cables and boxes

Split batts around cables Split batts to fit around electrical cables. Tear the batt in half, starting from the bottom. Slide one half behind the cable and lay the other half over the top. Cut batts around boxes Split and cut batts to fit behind and around electrical boxes. Slide half the batt behind the box. Then cut the front half to fit tightly around the box. Running a full batt in front of electrical cables leaves an uninsulated space behind. Avoid this by splitting the batt as shown. Then when you come to an electrical box, trim the insulation to fit snugly around it. Run your knife blade against the outside of the box to guide the cut. But don’t cut too deep or you risk nicking the wires. If you have plumbing pipes on an outside wall, insulate behind them, but leave the side facing the interior uncovered to allow heat from the house to keep the pipes warm.

Fit first, then cut to length

Can I use a shed as a tiny house?

Q: Can You Build a Tiny House out of a Shed? The short answer to this first question is “yes.” Plenty of people have already built their tiny...

Last updated Feb 15, 2020

What happens if a ramp is too steep?

Ramps that are too steep A steep ramp increases the likelihood of tipping backwards and also requires more energy to climb—ramps like this pose a...

Last updated Aug 9, 2018

These are the Best Shed Plans!

Comprehensive and Intuitive to follow. Build That Shed!

Learn More »

Promotion

Cut batts slightly long Cut batts to length by setting the top of the batt into the space and cutting against the bottom plate with a sharp utility knife. Leave an extra 1/2 in. of length for a tighter fit. We’re using unfaced batts that are sized to friction-fit into standard stud spaces (either 16-in. or 24-in. on-center studs). They’re also available precut to lengths that fit standard 8-ft. and 9-ft. walls. Buying precut batts eliminates some work, but you’ll still have to cut some batts to length. You could measure the space and cut the batt to fit, but a quicker method that’s just as accurate is shown below. Leave an extra 1/2 in. of length for a snug fit. We’re using unfaced batts because they’re easier to cut and install. In most climates, you’ll have to staple 4-mil plastic sheeting over the batts to form a vapor barrier. Check with your local building inspector for the recommended practice in your area.

Trim batts in place

Cut-in-place method Leave the batt folded in half and hold one edge against the edge of the stud. Slice down the length while holding the top of the batt. Cut against the stud face. Measure-and-cut method Alternate method: Press a straightedge down on the batt at the desired width and use it as a guide for the utility knife. Accurate cutting is essential (actually, slightly oversized batts are best). A batt cut too small leaves gaps and one cut too large bunches up and leaves voids. The photos show two methods of cutting batts to width. If you’re having trouble getting an accurate cut with the “eyeballing” technique, measure the width of the stud space and use the straightedge method instead. Add about 1/2 in. to the width to ensure a tight fit. It’s better to compress the batts a little than to leave gaps. Don’t worry if the batts bulge out a bit. The drywall will compress them tightly.

Fill gaps around windows and doors

What scent will keep raccoons away?

Since raccoons have a strong sense of smell, which they use to find convenient food sources, one can take advantage of this feature by using scents...

Last updated Jan 16, 2018

What poison kills mice instantly?

#1 Choice – Tomcat All Weather Bait Chunx Tomcat All Weather Chunx kills mice and rats fast. It contains a poison that doesn't let them last long...

Last updated Oct 31, 2022

These are the Best Shed Plans!

Comprehensive and Intuitive to follow. Build That Shed!

Learn More »

Promotion

Insulate windows and doors Stuff skinny strips of batting into spaces around windows and doors with a 3-in. wide putty knife. The insulation should fit snugly, but don’t pack it. The shim space around windows and doors is a prime spot for air leakage. Stop these leaks by reaching to the back of this space with the straw-type nozzle included with a can of expanding foam insulation and applying a bead around the perimeter. Let it cure at least an hour before stuffing the remaining space with a thin strip of fiberglass. Don’t pack the fiberglass too tight or it will bow the jambs and cause trouble with the operation of the window.

Video: Working With Mineral Wool Insulation

Required Tools for this Project

Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.

Dust mask

Safety glasses

Straightedge

Taping knife

Utility knife

Required Materials for this Project

Gloves

Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.

familyhandyman.com - How to Install Fiberglass Batt Insulation - The Family Handyman

Is it better to screw or nail joist hangers?

Should You Nail or Screw Joist Hangers? You can do either. According to Simpson, using their structural screws designed to work specifically with...

Last updated Jun 30, 2018

Can you put new cement on top of old cement?

You can put new concrete over old concrete. However, unresolved issues with your old concrete, such as cracks or frost heaves, will carry over to...

Last updated Jan 25, 2022

These are the Best Shed Plans!

Comprehensive and Intuitive to follow. Build That Shed!

Learn More »

Promotion

What is the most important virtue of a carpenter?

Physical strength and stamina One of the most important qualities of a good carpenter includes physical strength and stamina. This is important...

Last updated Sep 17, 2021

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

What temperature is too cold for potted plants?

Most potted or hanging plants, like petunias, are fine as long temperatures don't dip below 39 degrees, and especially if the temperature doesn't...

Last updated Apr 2, 2020