Should I screw directly into wood?

For rough construction, you can usually just power screws into place without drilling a hole. However, for finer woodworking projects, you risk splitting the wood without first drilling holes, especially near the end of a board. When driving screws, drill a pilot hole to prevent the wood from splitting.

woodworkingformeremortals.com - How to drive a screw (and not split the wood!)

How long can plywood shelves be without sagging?

Plywood panels over 3/4 inch in thickness are usually special order products. Thinner sheets of plywood can be glued together (laminated) to make a...

Last updated Sep 9, 2018

Can Neighbours stop you doing Airbnb?

Nuisance can be restrained by either civil proceedings for an injunction or action by the Local Authority under statute. Civil proceedings are...

Last updated Jan 18, 2021

Promotion

You can drive a screw with or without drilling a pilot hole first. It depends a lot on the type of screw you use and the project you are building. There is nothing wrong with drilling a pilot hole every single time though if you aren’t sure. For shop projects and larger construction projects made from 2x4s, I don’t bother drilling pilot holes. You can just drive the screws right into the lumber. It’s fast and efficient. You’ll have even better results with self-tapping screws. For rough construction, you can usually just power screws into place without drilling a hole. However, for finer woodworking projects, you risk splitting the wood without first drilling holes, especially near the end of a board. When driving screws, drill a pilot hole to prevent the wood from splitting. Drilling a pilot hole allows the threads of the screws to cut into the walls of the hole rather than forcing the wood fibers apart. This creates a stronger connection. Plus, a pilot hole will help the screw to drive in straight. To drill a pilot hole, select a drill bit that’s the same diameter or slightly less than the shank of the screw you are going to use. Use your drill to bore into the wood about as deep as the length of your screw. Press the side of the drill bit against your finger to keep it from wandering and slowly squeeze the trigger to get it started. You don’t need to press a lot of weight into the drill, just let the bit do its job. Be careful not to blast through the other side! Keep the bit spinning as you back it out.

How to select the correct drill bit size.

If you want the head of the screw to be flush with the face of the wood, use a flathead screw…one with a flat top and beveled sides on the head.

A flathead screw

Use a countersink bit or a countersink to add a beveled recess in the surface of the wood that the head of the screw will fit into. This will give your project a professional appearance. Use a countersink bit to create a tapered seat for the head of a wood screw.

A countersink.

Perfect fit! Clean and professional looking,

I like to use an impact driver to drive screws in place. A drill will also work, or, if you like twisting stuff by hand, you can use a regular old screwdriver. Set the point of the screw into the hole, holding it as perpendicular as you can with your fingertips and slowly pull the trigger to twist it in. If you have a tiny screw or big fingers, you can use needlenose pliers to hold the screw while you get it started. The biggest mistake you can make that causes the driver to slip out of the head is not keeping it aligned with the screw. Make sure you don’t tip the driver one. Just twist the screw in and stop when it’s is fully seated.

Using needlenose pliers to hold a screw while driving it into place.

Are square nails in Style 2022?

The jackpot of buzzy fashion and beauty trends, the '90s and Noughties continue to influence pop culture in 2022 — with the latest re-emergence,...

Last updated Jun 20, 2021

What's the softest wood in the world?

Balsa wood Balsa wood: the lightweight among the wood species With a density of 0.1 to 0.2 g / cm³, balsa is the softest wood in the world. Jul 30,...

Last updated Feb 21, 2020

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

What kind of nails to use for a shed?

For the substructure and framing of your shed where nails are hidden you should use coated nails such as vinyl coated sinkers or cement coated nails. These bond to the wood and will not pull up as easily and readily as uncoated nails.

shedking.net - Nails and Fasteners Used in Shed Building - Shedking

Nails and Fasteners Used in Shed Building

Nails are the most common fasteners used in shed building.

Nail lengths are indicated by the term penny, which is noted by the small letter 'd'. As nails get longer in length they get larger in diameter. Heavier construction nailing is done with common nails. A common nail has a thicker shank which gives it greater strength than other types of nails.

Common Nails Chart

The wide thick head of a common nail spreads the load and resists being pulled through. For the substructure and framing of your shed where nails are hidden you should use coated nails such as vinyl coated sinkers or cement coated nails. These bond to the wood and will not pull up as easily and readily as uncoated nails.

Nail Chart with Sizes and Uses

Nail Chart Showing Sizes and Uses

Framing Fasteners for Your Shed Construction

Using fasteners for framing your shed.

Some local counties may require you to use metal fasteners for your shed building project. The most common of these being a form of hurricane tie used on the connection of a roof rafter/truss to the top plate of the wall. The following pictures illustrate just a few of the more widely used fasteners for anchoring down your rafter and truss ends.

Simpson H2.5a shed roof rafter anchor

Simpson H10 hurricane tie

Not only do these fasteners create a more rigid structure but their modest cost will more then offset the benefit gained. These fasteners can be secured by using joist hanger nails which are short ribbed nails.