DIY Builds
Photo: cottonbro studio
Concrete blocks foundation is a possible solution and good for bearing weight. Concrete blocks are also small enough to move around under a shed wall. These are available at most building stores or even second hand. Patio stones are another possible solution.
it will be more than 4m high with a pitched roof or 3m high with a flat roof. If it will be within 2m of the boundary of the house, it must be 2.5m...
Read More »
Does a Detached Office Add Value to a Home? A detached office could be a selling point for some buyers, but that depends on what other spaces the...
Read More »
Top 11 Side Hustle Income Ideas to Make Six Figures Online Run a Blog. ... Dropshipping. ... Become an Influencer. ... Create an Online Course. ......
Read More »
Calculating the Slope Divide the length of the wheelchair ramp by the height. This will be the second number in your ratio. The first number is...
Read More »
The first thing you need to do when putting a foundation under a shed is to lift or move the shed. The smaller the shed, the easier this could be.
Log cabins have a long and illustrious history of longevity. They usually last twenty, thirty to even fifty years, if they are kept in good...
Read More »
Traditional asphalt shingles can range from $100 per square and $30 per bundle, while slate may run $800 to $1,600 per square, and $270 to $540 per...
Read More »You’ve raised and secured your shed, now what? You need to excavate for a floating slab, a footing and foundation wall, or a small pad to rest deck blocks or piers on. For most sheds with attached floors, a foundation wall or deck blocks are adequate. A shed with no floor is more likely to need a slab to act as a floor. I helped another buddy with a floorless shed a couple of years ago. We were able to raise and level his 12’x24’ shed using bottle jacks. We set the jacks on concrete blocks lifting against 4“x4”s bolted to the walls. The 4”x4”s extended about a foot beyond the shed’s corners. Once raised, we put blocks under the 4”x4”s so we could release the bottle jacks and stabilize the structure. With the shed lifted, we were able to dig out under the walls, and then use a bobcat to excavate the rest. We formed up the perimeter, tamped gravel in, put plastic down as a barrier, then put in a rebar grid. With that done, we had ready mix concrete delivered and poured the floor. We smoothed the concrete, left his daughter’s footprints in the corner, and waited 48 hours for it to cure. Once cured, we rolled out sill gasket, put the bottle jacks in place, and lowered the shed onto its new foundation. Almost as easy as it sounds…and we had the permits. Here are two pro tips to assist you with planning your slab foundation: If you’re building a foundation wall for your shed, the process is similar to the slab. You have to raise the shed to create a level base. Here are a couple more pro tip videos to assist you: I’ve helped do this several times, most recently a 20’x30’ century-old cabin built on stone pillars. We used hydraulic jacks to lift and stabilize the structure. Using spades and picks, we dug out for the footing and block foundation walls. It took us a couple of months, but we were successful! And no, it wasn’t easy!
Corrugated galvanized steel is one of the strongest, most durable roofing materials, since it lasts longer, is more resistant to wind, and absorbs...
Read More »
uPVC doors are 3 times for effective at maintaining cooler temperatures within a home. Wooden doors do not rust but are easily affected by termites...
Read More »
These are! They guide you every step of the way to complete your dream shed.
Learn More »
Outbuildings are considered to be permitted development, not needing planning permission, subject to the following limits and conditions: No...
Read More »
Design. The 2018 Olympic standards call for a 600-foot-long run, an 18-degree pitch and elliptically-curved walls that are 22 feet high and spaced...
Read More »