What happens if you don't grease your bike?

Without Bike Chain Lube: A dry chain will let out an ear-piercing squeal and won't shift smoothly. Eventually, it will rust, and it could snap midride. Lube It: Soak a clean rag with degreaser, such as Pedro's Oranj Peelz Citrus Degreaser.

bicycling.com - How to Use Bike Chain Lube to Keep Your Parts Moving Smoothly

What gets rid of rats permanently?

How to Get Rid of Rats Permanently Check for Signs of Entry. Seal and Secure all Entry Points. Eliminate all Food Sources. Remove Rat-Friendly...

Last updated Aug 7, 2022

Can I use concrete deck blocks instead of footings?

Instead of using footings, adding a level of gravel will give you the drainage aspect you are looking for. You can then add a frame of wood that...

Last updated Nov 17, 2021

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

For some, bike chain lube is an unglamorous necessity to keep moving parts moving. But for obsessives, bike chain lube transcends its utilitarian function and becomes the bike-maintenance equivalent of a fine wine, where quality is of the utmost importance.

Related Story The Right Chain Lube Can Save You Thousands

Whether you grab an affordable option or prefer the highest-quality version you can find, the fact remains that without the proper bike chain lube applied to the right places, your ride will come to a screeching halt. Here’s how to use bike chain lube and lubricate your bike’s other moving parts.

Chain

Without Bike Chain Lube: A dry chain will let out an ear-piercing squeal and won’t shift smoothly. Eventually, it will rust, and it could snap midride. Lube It: Soak a clean rag with degreaser, such as With your bike in a work stand, grasp the chain with the rag as you backpedal to remove grime from the rollers and side plates. Repeat until the chain is clean. Then, dry the chain using a clean rag and the same technique you used to clean it. To apply bike chain lube, deposit a drop on the top of each link as you slowly backpedal for a few revolutions, so the lube has a chance to work its way in. Wipe off excess lube—if you don’t, it can attract more dirt to your chain. Use a light, waterproof lube such as . For wet-weather conditions, try . Never Use: Motor oil—it contains acids and particles of metal that can compromise a chain’s strength and cause it to wear more quickly.

Clipless Pedals

Without Bike Chain Lube: Engagement and disengagement won’t be as smooth as it should be, and pedals may become impossible to remove from your bike. Lube Them: If your clipless pedal system has a visible spring (the area where your cleats engage into the pedal), apply a drop of T-9 every few rides to keep it rust-free and working well. Spread a coat of grease, such as on pedal threads every time you install pedals so they’ll actually budge the next time you go to remove them.

Never Use: Grease on the pedal springs. You’ll gum up the mechanism.

Should you leave all vents open in winter?

Closing Air Vents: Why It's a Bad Idea in Winter Making your heating system work harder to bring the temperature up in all rooms of the house....

Last updated Feb 27, 2019

Is Baltic birch better than birch plywood?

When it comes to strength and stability, Baltic birch is hard to beat. The wood has about twice as many plys as standard birch plywood, and each...

Last updated Apr 21, 2018

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

Cables

Without Bike Chain Lube: Cables won’t glide through housings as smoothly, which negatively affects shifting performance, and they’ll be more prone to rusting in wet conditions. Lube Them: Shift the rear derailleur to the easiest gear/largest cog (front derailleur to the hardest gear/big chainring). Then, without pedaling, click your shifter to upshift to the hardest gear/smallest cog (or the small chainring in front). This will result in a nice amount of cable slack, and on some bikes, allow you to slip the housing out of the slotted cable stops and coat the cables thoroughly. Apply a few drops of T-9 to your fingertips and slide them along the length of the cable until it’s covered in a thin film. Wipe dirt from your cables, paying special attention to where they run through the cable guide underneath the bottom bracket. Use the same lube and method of application on your brake cables. Never Use: WD-40—it’s a solvent, not a lubricant. If your cables and housings are so gummed up that you need a solvent, you’re better off replacing them than performing makeshift maintenance on them.

Pivot Points

Without Bike Chain Lube: The points on which the individual parts of your brakes and derailleurs pivot will not move as smoothly and will invite rust. Lube Them: Drip T-9 onto each pivot point (rear derailleur; front derailleur; rear brake; front brake) every few months (more if you ride in wet conditions) to keep them protected and working well. Wipe off excess bike chain lube so it doesn’t attract dirt. Never Use: Lubricant on brake pads, rotors, or rims. If you do, you’ll have a hard time slowing or stopping. If you accidentally get lube on disc brake rotors or pads, you’ll need to get new pads to be safe.

Derailleur Pulleys

Should you water tomato plants everyday?

Tomato plants need to be watered daily or every other day unless you have had recent rain. The plants need 1-1.5 inches of water per week, but...

Last updated Jul 20, 2022

Why do doors in Japan open outwards?

The front door usually opens outward, which is opposite of in Western houses. This is because Japanese people do not wear shoes in the house, they...

Last updated Feb 28, 2022

Promotion

Without Bike Chain Lube: Not only will you go crazy trying to track down the cause of that annoying squeak (commonly caused by neglected derailleur pulleys), but the pulleys also won’t rotate freely. Lube Them: Wipe off any built-up grime on your derailleur pulleys with a clean rag and degreaser. Then apply a small drop of bike chain lube, such as , to the bearings at the center of the pulley. Backpedal a few revolutions, then use a clean rag to wipe off any lube that didn’t work its way into the bearings. It can get messy, so use sparingly. Never Use: Grease—it’s way too heavy for this application, and it will gunk up pulley bearings and attract crud.

Seatpost

Without Bike Chain Lube: Your seatpost isn’t technically a moving part per se, at least until you go to remove or adjust it. It’s important to keep your seatpost greased, and check it every so often, so that it doesn’t seize up and get stuck in place. Lube It: Fully remove the seatpost. Wipe off any grit and old grease, including inside the frame. Apply a thin layer of grease directly to the seatpost on the area that will sit inside the frame. Standard bike grease will work, though you might want to use either an or compound. Never Use: Too much grease. This could cause your seatpost to slip when it’s weighted.

📹 Watch: How to Wash Your Bike Like a Pro

bicycling.com - How to Use Bike Chain Lube to Keep Your Parts Moving Smoothly

What type of storage shed lasts the longest?

Vinyl sheds tend to be more durable. Vinyl sheds do not crack easily and are more weather resistant. They can usually withstand extreme...

Last updated Dec 26, 2020

What is the most stable flooring?

8 Most Durable Flooring Options for Heavy Foot Traffic Bamboo. Resiliency. Ceramic and Porcelain. Laminate. Solid Hardwood. Engineered Wood....

Last updated May 13, 2018

Promotion

How much furniture will a 10x10 storage unit hold?

A 10x10 unit is a good size for the stuff found in two bedrooms, an entire family room or a modest one- or two-bedroom apartment. A few large...

Last updated Jun 1, 2020

Promotion

How high off ground should shed be?

4”-6” inches How high should a shed be off the ground? Generally speaking, you will want the floor of your shed to be 4”-6” inches off the ground....

Last updated Dec 7, 2020