Photo: Monstera

What kind of walls need a double top plate?

Wood stud walls shall be capped with a double top plate installed to provide overlapping at corners and intersections with bearing partitions. End joints in top plates shall be offset at least 24 inches (610 mm). Joints in plates need not occur over studs.

sbcmag.info - Single Top Plate in a Wood Stud Wall | SBC Magazine

How much will it cost to build a lean-to?

A lean-to will cost around $15 to $17 per square foot, depending on whether you go with the open option (like on this building), or the enclosed...

Last updated Jul 6, 2022

Can I put plywood on top of plywood?

Install a layer of at least ½” or preferably 5/8” ply over the existing planks. This is particularly important if your old sub floor has lumps and...

Last updated Mar 2, 2019

Are shed plans easy to follow?

These are! They guide you every step of the way to complete your dream shed.

Learn More »

Promotion

Weigh the pros and cons of using a

single top plate in a wood stud wall.

Question

In a residential home, is it possible to use a single top plate in a wood stud wall supporting a trussed roof? Is it beneficial to use a single top plate?

Answer

In answer to your first question: Yes, it is possible to use a single top plate in lieu of the traditional double top plate in a wood stud wall. While a single top plate isn’t the norm, it cuts the volume of lumber in the top plate in half and can contribute to a building’s overall energy efficiency by reducing thermal bridging through the lumber and allowing a bit more space for insulation. This increases the thermal efficiency of the wall system. The 2012 International Residential Code (IRC) allows for the use of a single top plate in a wood stud wall if the design meets specific requirements. IRC Section R602.3.2 outlines the top plate requirements, and then the exception lists the qualifications for using a single top plate. The 2012 IRC Commentary further explains the requirements for a single top plate in Figure R602.3.2 (see Figure R602.3.2). Wood stud walls shall be capped with a double top plate installed to provide overlapping at corners and intersections with bearing partitions. End joints in top plates shall be offset at least 24 inches (610 mm). Joints in plates need not occur over studs. Plates shall be not less than 2-inches (51 mm) nominal thickness and have a width at least equal to the width of the studs. R602.3.2 Top plate.Wood stud walls shall be capped with a double top plate installed to provide overlapping at corners and intersections with bearing partitions. End joints in top plates shall be offset at least 24 inches (610 mm). Joints in plates need not occur over studs. Plates shall be not less than 2-inches (51 mm) nominal thickness and have a width at least equal to the width of the studs. Exception: A single top plate may be installed in stud walls, provided the plate is adequately tied at joints, corners and intersecting walls by a minimum 3-inch by 6-inch by a 0.036-inch-thick (76 mm by 152 mm by 0.914 mm) galvanized steel plate that is nailed to each wall or segment of wall by six 8d nails on each side, provided the rafters or joists are centered over the studs with a tolerance of no more than 1 inch (25 mm). The top plate may be omitted over lintels that are adequately tied to adjacent wall sections with steel plates or equivalent as previously described. To summarize, in order to use a single top plate per the IRC’s prescriptive requirements:

What is America's number 1 foundation?

BareMinerals Original Loose Powder Foundation SPF 15 There's no denying that this is the reigning champion among all powder foundations out there,...

Last updated Nov 4, 2018

What sits on top of the sill plate?

The first floor frame is built on top of the sill plate. A home's floor frame consists of common joists which span across the foundation walls, and...

Last updated Feb 20, 2018

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

• Plate must be tied at the joints, corners and intersecting walls.

• Minimum 3" x 6" x 0.036" galvanized steel plate must be fastened to each wall or segment by six 8d nails. • Trusses, rafters or joists must be centered over the studs with a tolerance of not more than 1". The minimum connector and fastener schedule, along with the 1" tolerance, provide the strength needed to transfer loads from member to member when less wood is used in the wall. When trusses are used on a project, the stud spacing can be increased to 24" o.c., which removes more lumber, improves energy efficiency and still allows a continuous load path.

Is It Beneficial to Use a Single Top Plate?

Determining if a single top plate is more beneficial than a double top plate depends on the project and the professionals involved. A single top plate can decrease lumber use and boost energy efficiency, but less lumber also decreases the bearing capacity of the top of the wall. The fastener requirements for a single top plate compensate for less lumber while still providing adequate connections of framing. The tolerance requirements ensure adequate bearing capacity by directing the loads from the framing above the top plate directly into the studs below. To determine if the use of a single top plate is beneficial, increased energy efficiency and reduced lumber usage must be weighed against the cost of galvanized steel plates and the attention required to ensure framing is placed within the given tolerances.

sbcmag.info - Single Top Plate in a Wood Stud Wall | SBC Magazine

Are plastic sheds worth the money?

Value for Money Plastic sheds are priced well, especially the larger ones. They give a lot of storage for the dollars spent. And although they do...

Last updated Jul 24, 2022

What can I build without planning?

23 Projects You Can Do Without Planning Permission Interior renovations. ... Single-storey extensions. ... Build a conservatory without planning...

Last updated Oct 19, 2020

Promotion

How many years does a wood foundation last?

In case you didn't know; accelerated laboratory testing of modern pressure treated materials indicates a lifetime of over 100 years with no serious...

Last updated Nov 4, 2020

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

What is the heaviest wood in the world?

77.1 lbs/ft3 (1,235 kg/m3) From the Spanish “quebrar hacha,” which literally means “axe breaker.” Aptly named, wood in the Schinopsis genus is...

Last updated Jan 28, 2021