What materials do I need to build a 12x16 shed?

12×16 Shed DIY Plans | Free Woodworking Guide FLOOR. 10 – 2×6 Pressure Treated Lumber: 15′-9″ 2 – 2×6 Pressure Treated Lumber: 12′-0″ ... WALLS. 51 – 2×4 Lumber: 7′-5 3/4″ 2 – 2×4 Lumber: 11′-5 ” ... SIDINGS. 16 – 4′ x 8′ Plywood Siding Panel T1-11 (496SF) PURLIN & ROOF. 12 – 2×4 Lumber: 17′-8″ ... TRIM. 8 – 1×4 Lumber: 7′-11″ HARDWARE.

buildblueprint.com - 12x16 Shed DIY Plans - Gable Roof - Build Blueprint

How much money can you have in the bank and still get the pension?

It comes down to the amount of savings you already have, plus all sorts of asset types combined. For example, if you are a single homeowner you can...

Last updated May 4, 2020

What do modern sheds cost?

Modern-Shed Cost: Starting around $10,000 for the smallest sheds, much more expensive for larger sheds. May 22, 2020

Last updated Mar 21, 2019

Are shed plans easy to follow?

These are! They guide you every step of the way to complete your dream shed.

Learn More »

Promotion

Get the complete 12×16 Shed Plans – PDF Instant Download:

12×16 Shed DIY Plans | Free Woodworking Guide

Material and Cut List

FLOOR

10 – 2×6 Pressure Treated Lumber: 15′-9″

2 – 2×6 Pressure Treated Lumber: 12′-0″

5 – 4×4 Pressure Treated Lumber: 12′-0″

6 – 23/32″ Tongue and Groove Plywood 4′ x 8′ Sheet (cut to size)

WALLS

51 – 2×4 Lumber: 7′-5 3/4″

2 – 2×4 Lumber: 11′-5 ”

4 – 2×4 Lumber: 12′

2 – 2×4 Lumber: 16′

4 – 2×4 Lumber: 15′-5″

SIDINGS

16 – 4′ x 8′ Plywood Siding Panel T1-11 (496SF)

TRUSS

20 – 2×4 Lumber: 8′-0″

10 – 2×4 Lumber: 12′

10 – 2×4 Lumber: 3′-2 1/2″

4 – 2×4 Lumber: 2′-8 7/8″

40 – Tie Plates: 7″ or various

Metal Gusset (reference detail for sizing)

PURLIN & ROOF

12 – 2×4 Lumber: 17′-8″

10 – 4′ x 8′ 3/4″ Plywood Sheet (295SF)

Roof Underlayment (295SF)

3-Tab Roof Shingles (295SF)

TRIM

8 – 1×4 Lumber: 7′-11″

HARDWARE

3 1/2″ Galvanized Steel Nails

2″ Deck Screws

2″ Galvanized Finishing Nails

1 1/2″ Drilling Roofing Screws

*Full materials list included in PDF version

Step 1 – Foundation and Floor

Start with selecting a proper site for the shed foundation, ideally a flat solid surface away from any large trees. The first step is cut ten 2×6 lumbers to 15’-9” length, and two 2×6 lumbers to 12’-0. Next, place the five 10’ 4×4 lumbers parallel to each other at 48” apart. Then, assemble the 2×6 perimeter frames on top, this will outline the overall floor frame. Drill pilot holes through the joists and secure with 3 ½” screws. Finally, install the eight 2×6 floor joists at 16” O.C. to complete the foundation. After the floor frame is secured, cut the tongue and groove 23/32″ plywood to size and attach to the frame. You’ll need 6 full sheets to cover the 192SF floor area. These sheets usually come in standard sizes of 48” x 96”. Insert 2” deck screws every 8” along the joint, don’t leave any gaps between the sheets. Refer to the cut pattern below:

Step 2 – Walls

Start with the front wall frame first, all frames used here are 2 x 4’s (except the door and window header which are 2 x 6’s). Cut two 2 x 4’s to 12’-0” in length, these will be used for the top and bottom plates. Then, cut eight 2 x 4’s to 7’-5 3/4” for wall studs, these will be placed per spacing illustrated below. You’ll also need to cut out a 11’-5” 2 x 4 for the double top plate. Drill pilot holes through the plates and insert the 3 ½” screws into the studs to secure in place. Align the frame edges and make sure all corners are flush for a professional result.

See detailed Door and Window framing instructions here:

Is steel guitar easy to learn?

The Pedal Steel Guitar is considered one of the most difficult instruments to master. It can take many years to be proficient, but some who have a...

Last updated Apr 10, 2018

How do you prep a pad for a shed?

Gravel Pad in Box Prepare Construction Site. Remove all vegetation and rocks from the building area. ... Digging Out. Remove any grass from within...

Last updated Mar 16, 2019

Promotion

The 2×4 studs holding up the door header need to be cut at 6′-3 1/2″. Next up is the building up the shed’s back wall. Cut two 2 x 4’s to 12’ length, and 12 more 2 x 4’s to 7’-5 3/4” length. Then cut out a 11’-5” 2 x 4 as the double top plate. Follow the framing plan below. Space the wall studs to 16” O.C. matching the width of the front wall frame. Drill pilot holes through the plate and insert 3 ½” screws to secure the studs. Continue the build by assembling the 2 side wall frames. Cut two 2 x 4’s lumber to 15’-5” as top and bottom plate, then a full 16’ 2 x 4 as the double top plate. then cut 12 2 x 4’s to 7’-5 3/4” for the wall studs. The single door studs are 6’-3 ½” in length.

See door and window detail for detailed build dimensions.

Step 3 – Roof & Truss

The roof will require a total of 10 identical gable kingpost style trusses, installed 20” O.C. There are also two cross bracing placed on both ends for added stability. The trusses are designed to have an overhang of 10” on both sides. Refer to the truss detail page for dimensions and assembly instructions.

Tip: make 1 truss first and make sure everything fits in place.

Refer to the full gable truss dimensions and assembly below, use wooden gussets to joint all the truss members together. Construct a single truss first, in order to test out the overall fit. The next step is to add purlins on top of the trusses. Measure and cut out 12 2 x 4’s to approximately 17’-8” in length. Center the purlins to leave about 10” of overhang, secure to the trusses with 3 ½” nails. After all the purlins are secured in place, measure and cut the 3/4” plywood panels to size. These sheets usually come in standard 96” x 48” size, you’ll need about 295SF to cover the entire roof area. Insert 2 ½” nails into the purlins at about every 10” to lock the plywood sheets in place. Next up is installing the exterior shed sidings, it’s easier to do this first before adding in the roof trims. Full exterior panel cut and assembly plans available in the full PDF version. Measure and cut 16 T1-11 plywood siding panels to size. These shed panels are designed to interlock, so plan them out accordingly. These siding panels also come in standard sizes of 96” x 48”, you’ll need about 496SF to cover the entire shed. For the front wall siding, measure and cut out the door and window openings before installing. The rough double door opening is 72” x 77”, rough opening for single door is 36” x 77”, and the optional window opening is 2’-11 ¼” x 2’-11 ⅜”. Cover the entire roofing area with roof underlayment or tar paper, this is a waterresistant barrier material to keep the wood structures dry. You’ll need about 296SF to cover the roof.

Can you use too much bubble wrap?

However, too much bubble wrap or other materials can strain the top of the box and cause it to burst open during shipping, so be mindful of how...

Last updated Jul 8, 2021

Which door hinge holds the most weight?

How Much Weight Can Each Type of Hinge Hold? Let's start with the basics: a residential duty hinge can hold between 200 and 400 pounds. A...

Last updated Dec 6, 2021

Promotion

You can also add a ridge cap on top of the gable roof, this strengthens the ridge of the roof and prevents potential leakage. Finally, we need to lay out the roof shingles (295SF of 3-tab roof shingles). Start at the bottom of the roof, measure and mark every increment height all the way to top of the roof. Use glue or glue strip along the rake edge and drip edge. Then, insert 2 ½” nails to secure in place. Tip: You can select the roof shingle material to match the roofing material of the main house, for a unified look! Get samples from your local hardware or home renovation store to get a close match.

Step 4 – Trims, Door, and Window

For the wall trims, measure and cut eight 1 x 4 lumbers to 7’-11”, trim the top angle as needed. Align and secure these trims with 2 ½” nails into the wall frames. As for the double door trim: use a 6’-7” long 2 x 6 as the header trim, and two 6’-5” long 2 x 4’s as frame trims. The single door trim will need two 6’-5” 2×4’s and a single 3;-7” 2×6 header trim. The window will require a 42 ⅜” 2 x 6 header, and 35 ¼” side trims. Secure all trims to the studs with 2 ½” nails. Add in the shed door and optional window. Refer to double door and window plans for build details.

Step 5 – Paint

You’ve completed your very own 12×16 Garden Shed! Now it’s time to paint the masterpiece. First, wipe off any dirt or dust off the T1-11 siding surface. Prime the siding with a heavy acrylic primer, a single thorough coat will do the job. It’s best to use a small brush to fill in the grooves and corners first, and then use a larger roller to cover up the flat areas. Let it sit and dry. Then apply two coats of exterior grade acrylic paint, allow enough time between coats to completely dry.

buildblueprint.com - 12x16 Shed DIY Plans - Gable Roof - Build Blueprint

How do you know where to drop anchor?

1. Location: Choose an Area Clear of Boats and Underwater Obstacles. Decide on an area to drop anchor that is clear of other vessels and any...

Last updated Jan 4, 2020

What is a 1 2 3 mix for concrete?

Concrete is made from cement, sand, gravel and water. In making concrete strong, these ingredients should usually be mixed in a ratio of 1:2:3:0.5...

Last updated Nov 18, 2021

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

How many feet can you cantilever?

The recommended maximum extension for a cantilevered exterior deck is four feet. In this situation, 2X joists should extend back into the floor at...

Last updated Nov 17, 2022

Promotion

Why do English homes have sinks in bedrooms?

Indoor plumbing was an innovation in the Victorian era. In middle-class homes having a separate room for bathing was often a luxury. Bathroom sinks...

Last updated Aug 24, 2021