What size hole do you drill for electrical wire?

Most electricians keep their inspector happy by drilling 3/4-in. holes dead center on a 3-1/2 in. wide stud. This gives them a hole large enough to run two electrical cables and leave 1-3/8 in.

familyhandyman.com - Drilling Holes: Notching and Boring Holes in Wood Studs

How do you stop wood from swelling?

Sanding the sticky areas of the door should do the trick for this issue. Reducing indoor humidity can help in preventing wood doors from swelling....

Last updated Jul 21, 2020

Do metal sheds need to be anchored?

The base for a metal shed is important as, unless you have purchased a separate timber floor kit, this will also provide the floor for your shed....

Last updated Dec 24, 2019

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

Drilling Holes: Notching and Boring Holes in Wood Studs

How much wood are you allowed to cut out of a stud?

Family Handyman Building codes specify allowable sizes and locations for holes and cuts in studs. Here's a handy guide to those requirements that will keep your building standing tall. You might also like: TBD

Overview

You get two benefits when you build or remodel with wood studs. The studs provide the strength and framework for the structure, and the empty spaces between the studs serve an important function, too: They provide the perfect place—a veritable vertical freeway—to run pipes, vents, drains, wires and ductwork. The drawback? When you have to run pipes, ducts or wires horizontally through the studs, you often have to notch or drill holes—sometimes big ones—to get them to their destination. But you can't just drill and saw away. There are rules you have to follow for drilling and notching studs. Some rules help ensure the structural integrity of a wall. And others are aimed at protecting pipes and wires that could be damaged by screws, nails and other fasteners driven into a wall. Figure A: Rules for Notching and Boring Studs Building codes allow you to drill bigger holes and cut bigger notches in non-load bearing walls than in load-bearing walls. Figure A is also available as a pdf in Additional Information below.

You have to keep the structure strong

There are LOTS of building codes dictating just how large a hole or notch you can cut (Fig. A). The technical yet important rules are: Holes in bearing wall studs (exterior and interior walls that bear the weight of the roof and/or other stories above) may not exceed 40 percent of the width of the stud. Notches in bearing wall studs may not exceed 25 percent of the stud’s width.

Holes in non-bearing walls can’t exceed 60 percent of their width.

Notches in non-bearing walls can’t exceed 40 percent of their width.

The edge of a hole must be at least 5/8 in. from the edge of a stud. To appease the plumbing gods, the codes have made at least one notable exception: In bearing walls you can bore 60 percent size holes—as long as you double up the studs and don’t drill through more than two successive pairs of these doubled-up studs (Fig. A). This allows you to run a short section of “drain, waste, vent” (DWV) pipe through a 2×4 wall without beefing up the whole wall to 2×6 dimensions.

There are other, less specific guidelines:

Can I keep a tumble dryer in a shed?

In short, yes a tumble dry can be put in a shed, provided precautions are taken to keep them both safe. Before installing the tumble dryer, the...

Last updated Mar 11, 2021

Can I grow seeds in a potting shed?

Seeds, seeds, seeds A potting shed is ideal if you love to get seeds going and don't want to leave all those seed trays on windowsills in the...

Last updated Oct 7, 2021

Are shed plans easy to follow?

These are! They guide you every step of the way to complete your dream shed.

Learn More »

Promotion

When possible, notch a stud near the top, rather than the bottom. Don’t locate holes and notches near large or loose knots, and don’t group too many in the same area of the stud. Finally, notch only when necessary; holes weaken it less than notches. In areas subject to high winds, earthquakes or tornadoes, maintaining wall strength is particularly important. Furthermore, studs with too much “meat” removed tend to bow and warp. Your building inspector will be on the lookout for overzealous notching and boring, so follow the rules. In reality, few walls ever out-and-out collapse during everyday duty from being riddled with too many holes and notches. But there are LOTS of cases in which unprotected or inadequately protected pipes and wires have been nicked and punctured by screws and nails. Any plumber or electrician will tell you that’s what you REALLY need to watch out for!

Protect those wires and pipes

The National Electrical Code requires holes containing non-metallic cable (often called Romex) or flexible metal-clad cable (the type you buy with the wires already in it) be set back 1-1/4 in. or more from the edge of a stud (Fig. A) to protect the wires from nails and screws. (The 1-1/4-in. screws and nails used to secure 1/2-in. drywall penetrate the studs about 3/4 in.) Most electricians keep their inspector happy by drilling 3/4-in. holes dead center on a 3-1/2 in. wide stud. This gives them a hole large enough to run two electrical cables and leave 1-3/8 in. of protective wood on each side. If they need to run more wires, they’ll drill more holes directly above the others. If a hole comes any closer than 1-1/4 in., your inspector will make you install a 1/16-in. thick protective metal plate (Fig. A). Available in 3-in. and longer lengths, the plates can be found at home centers and hardware stores. The mechanical codes for plumbing and heating, ventilation and cooling (HVAC) systems also dictate that holes containing pipes be set back 1-1/4 in. from the edge of a stud to protect the pipes from fasteners. Those that come closer need to be covered by metal plates; for big pipes, use a long protective plate. Electricians and plumbers spend lots of time drilling big holes, so they know a few tricks to make the job easier (or avoid it altogether). Figure B: Drilling Use a right angle drill with hole saw bits for boring large holes. Keep the holes centered on the studs and a consistent height off the floor.

How far apart should shed Skids be?

The maximum distance between the skids should be 6 feet at center for 2×6 floor joists. If the distance is greater, add 1 or more skids between the...

Last updated Sep 6, 2022

What size plywood should I use for furniture?

Plywood for Furniture Most cabinet construction uses ¾” plywood, or else ½” plywood, which is usually less expensive, and makes the finished piece...

Last updated Jan 22, 2019

Are shed plans easy to follow?

These are! They guide you every step of the way to complete your dream shed.

Learn More »

Promotion

Tips for less drilling and notching

Figure C: Angled holes Angled holes are tough to pull wires through because the cable catches on the sharp edges. Figure D: Square holes Holes square to the face of a stud are easy to pull wires through. Before beginning any project, plot out exactly where large pipes and ducts will run and determine how you’ll get them there. Wherever possible, run large pipes and ducts vertically into unfinished attics or basements, then install elbows and run the pipe or duct horizontally below the floor joists or above the ceiling joists. Build 2×6 stud walls where DWV pipes and holes exceed the limits shown in Fig. A. Rent a right angle drill and use Selfeed or hole saw bits for boring large holes (Fig. B). The right angle drill allows you to drill holes square to the stud face. Holes drilled at an angle will wind up oval and therefore larger. Drill holes at least 1/4 in. oversize, especially for hot water pipes. If you don’t, they’ll make annoying sounds as they expand, contract and rub along studs. Joist hanger manufacturers sell wrap-around, stud reinforcer plates (Fig. A). Ask your inspector if they are permissible in special situations. When boring electrical holes, keep them square to the stud for easier wire installation, or pulling. This may seem trivial, but angled holes like those shown in Fig. C “catch” the wire and keep you from pulling wire through more than two or three studs at a time. Holes in a line (Fig. D) let you pull wire through an entire wall length of studs at one time.

Required Tools for this Project

Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.

Reciprocating saw

Tape measure

Required Materials for this Project

The best tool for drilling holes in studs is a right-angle drill with self-feeding bits. Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.

familyhandyman.com - Drilling Holes: Notching and Boring Holes in Wood Studs