What size joist should I use for a shed?

Often people will oversize their joists, thinking that 2x10s “look” right for a floor frame, when in reality 2x6s or 2x8s might be more than adequate and can save money. Don't forget to use galvanized nails for constructing this portion of the shed frame!

finehomebuilding.com - Building a Shed? Get the Site, Footings, and Floor Frame Right

Should roof vents have screens?

Screen vents for your attic are the base of your roof's ventilation system, which allow adequate airflow and help protect your roof from building...

Last updated Dec 18, 2018

Is a metal shed better than wood?

Metal sheds are more durable as they are fire, insect, rot, and weather resistant. They can rust, but they are more durable to the elements vs. wood.

Last updated Dec 12, 2019

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

You may never look at it again, but one of the most important parts of a shed structure is the floor frame. Not only will the building method change depending on your overall design, but it’s also important to think about moisture, load paths, lumber spans, and the basics of proper framing.

Start with a solid base

Unless you live in an area that’s so dry that moisture accumulation isn’t a concern, or have soil that drains exceedingly well, it’s a good idea to cover the area under the shed with several inches of coarse gravel (3/4″ is a common option). The idea behind the coarse gravel is that it defeats the natural process of capillarity, which causes water to rise up from the ground after rainfall. Forgive my simplistic builder’s summary of capillarity, but it’s essentially a function that allows water to be sucked from large areas to smaller areas, regardless of gravity. The spaces between pieces of gravel are essentially large pores, and are large compared to the smaller pores between grains of soil, sand, or whatever substrate is below the gravel. So, by adding a layer of gravel, you’ve eliminated the ability of water to wick upward into your shed. Gravel also aids drainage and evaporation, both of which are crucial under a shed. You can’t always stop water, but you can provide it a means for running off or drying. If you lay a bed of gravel you can actually build the shed floor frame right on the gravel. This is a common approach when buying a factory-built shed. You’ll want to check with your local building department to make sure they’re ok with this (most I’ve encountered consider small detached structures under a certain square footage to not require permanent footings). Another common approach is to set concrete blocks on the ground, first digging out the grass and topsoil, to a depth of maybe 6 or 12 inches below grade, and fill the hole with gravel. Use solid concrete blocks, not the hollow variety used in masonry wall construction, and remember that blocks are commonly available in several sizes, which is handy when it comes to getting close to level. As a rule I don’t stack blocks more than 2 or 3 high (depending on block size) because the higher the stack the lower the stability. In situations where the ground is sloping severely, or you want a more permanent connection with the site, you should choose poured concrete footings that extend below the local frost depth. If the shed will be on stacked blocks or poured footings you’ll need to consider the number of footings and how they are spaced. This is directly tied to the type of floor frame you will be using.

The best shed-floor framing is simple and sturdy

Do powered roof vents work?

Although power attic ventilators can provide relief in the summer, how they go about doing that is often not ideal or cost-effective. For one, they...

Last updated Dec 27, 2019

What is the lifespan of a tiny house?

Tiny homes can last between 7-10 years depending on materials and regular maintenance. However, Park Model units last longer and are aesthetically...

Last updated Jul 21, 2018

Promotion

In most cases a shed is built atop a floor frame of dimensional lumber and plywood or OSB. This method is fast, and follows conventional and familiar framing techniques. Joists run the short direction, typically spaced every 16 inches, and are captured by rim joists on the long sides of the shed. If the joists are set atop a plate (see picture) then you won’t need joist hangers to reinforce the ends of each joist. If no plates are used, you must use joist hangers. Also, pay attention to the span of the lumber you’re choosing for the floor, information which can be found readily on the internet, in building code books, or at your local building department. Often people will oversize their joists, thinking that 2x10s “look” right for a floor frame, when in reality 2x6s or 2x8s might be more than adequate and can save money. Don’t forget to use galvanized nails for constructing this portion of the shed frame! Standard (“bright”) framing nails are not compatible with pressure-treated lumber!

Happy building!

– Justin

Follow editorial director Justin Fink on Instagram @mrjfink

finehomebuilding.com - Building a Shed? Get the Site, Footings, and Floor Frame Right

What does a 2 0 door mean?

The nomenclature of doors is as follows: the width is specified by 2 or 3 numbers that indicate the feet and inches of the door a 2-0 [written 20]...

Last updated Jan 8, 2018

Do raccoons like Irish Spring soap?

Soap the yard Raccoons use their superb sense of smell to forage for food, and some scents are really effective at keeping them away. The...

Last updated Feb 1, 2022

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

Do I need bearers for a shed on concrete?

To ensure the floor stays dry, we strongly advise that bearers are used, even with concrete/paved bases as this allows air circulation and prevents...

Last updated Feb 25, 2018

Promotion

What is the longest lasting shed?

Vinyl sheds tend to be more durable. Vinyl sheds do not crack easily and are more weather resistant. They can usually withstand extreme...

Last updated May 10, 2018