Why is the wood on my deck curling up?

The combination of 'too moist' conditions on the bottom of the deck board and too dry on the top, creates internal stresses in the wood. The wood will cup upwards naturally to relieve the internal stress.

mataverdedecking.com - What Makes Hardwood Decking Cup and How Can I Prevent It?

Does a garden studio add value?

Will a garden room add value to my property? “Not only does a garden room attract more buyers to your property, but a high-quality garden room can...

Last updated Dec 28, 2020

What are the cons of a Barndominium?

List of the Cons of a Barndominium Barndominiums are not immune to corrosion. ... There is still a cost element to consider with barndominiums. ......

Last updated May 26, 2021

Can I build my own shed?

Yes, with the right plans you can build your dream shed.

Learn More »

Promotion

When there is an imbalance in a wood board, it may tend to cup. How does this happen? Occasionally (mostly with softwoods) the orientation of the grain in the board facilitates the board to cup. But it is powerful natural external forces that causes the most movement to happen. These forces, UV rays and moisture, wreak the most havoc on hardwood deck boards. This is especially true with exterior woods, where there are many weather factors in play. The two most powerful conflicting external weather forces; solar rays and moisture, are at war with your decking. The heat on the top of the deck draws up the moisture from below the deck. And then there is the poor deck board, caught in the middle of this epic struggle, literally pinned down in place. The top of the board is shrinking, and the bottom of the board is expanding. Help!! If the deck boards could talk, they would be screaming in pain. When the external forces become too powerful for the wood, the wood will move, typically cupping upwards at the outside edges.

Key Factors Causing Deck Boards to Cup

Too much sun on the top, combined with too much moisture below.

Too little clearance between the ground side moisture and the bottom of the deck boards

Inadequate ventilation below the deck

Improper drainage below the deck

High exposure to sunlight above the deck

Minimal gap space between the deck boards

Insufficient fastening of the deck boards

Any of the individual factors listed above can create conditions for wood movement and deck boards to cup. When several of these conditions are present together, you can expect problems. The combination of 'too moist' conditions on the bottom of the deck board and too dry on the top, creates internal stresses in the wood. The wood will cup upwards naturally to relieve the internal stress.

Unventilated, poorly drained deck shows wood deck boards cupping

Does a hot garage make your house hotter?

In addition to helping to bring up the temperature inside your home, there are other reasons why a hot garage can be bad news. Your garage can...

Last updated Jan 24, 2019

Is it hard to get a loan to build a Barndominium?

Regarding barndominiums, they can be financed, whether you choose to finance them yourself or through a loan. As they are not as popular as regular...

Last updated Apr 12, 2021

Promotion

We created a convenient PDF for you of this information:

How Can You Minimize the Amount of Cupping in Deck Boards?

Creating a balanced deck design and structure starts in the planning and design process. Short of putting a roof over your deck, there's not a whole lot of things you can do to minimize the sunlight. So, controlling and minimizing the amount of moisture below your deck is your best option. Here is a list of some best demonstrated practices for long-lasting deck performance: Build decks as high above grade as possible. 30” is considered the minimum for best performance. Anything less than 30” is considered a ‘low clearance’ deck. Make sure there is proper grading below your deck. pitch the ground away from your home or structure. Get the water out of there! Standing (or sitting) water creates an unacceptably moist below-deck environment. Make sure there is adequate drainage to allow rain and bulk water to escape from below the deck. Some landscape architects and master deck builders use landscape fabric below the deck to keep the moisture in the ground. Some experts will then place a layer of gravel on top of the fabric to handle rain water from above. And since the ground is already pitched it flows out from below the deck at a controlled rate. Plan adequate below-deck ventilation . Ventilation on three sides is ideal. Proper air flow helps eliminate unwanted moisture. Two sides with cross-ventilation is next best.

Always properly acclimate your deck boards to site conditions - before installation.

Pre-finishing your deck boards with an appropriate sealer on all four sides, before installation, helps protect your investment. Here's what can happen without proper prior planning Oh my! When the cupped deck boards in this picture were removed for inspection, the top of the boards were bone dry. The bottom of the deck boards are literally soaking wet. In addition to the expected cupping in these conditions, you can see black mold growing where the deck boards were sitting on the joists. This is a bad environment for the decking and the joists. Low clearance decks are the worst-case scenario for deck boards. Limited air flow and imbalanced moisture conditions are extremely tough on wood decking. Special steps and design considerations are needed for best performance.

What to use for siding on a shed?

11 Most Popular Shed Siding Options Vinyl Siding. ... Metal / Steel. ... Traditional Wood Siding. ... Engineered Wood Siding. ... LP Smartside...

Last updated Aug 5, 2019

What lowers property value?

Changes in the real estate market can lower the value of your home. Natural disasters and climate change can lower your property value because the...

Last updated Oct 5, 2022

Are shed plans easy to follow?

These are! They guide you every step of the way to complete your dream shed.

Learn More »

Promotion

Use thicker deck boards . 21 mm or 5/4 thick nominal decking is heftier and much less likely to cup as much as a thinner (1 x nominal thickness) deck board Narrower boards work best . 4” nominal (3-1/2” actual) wide deck boards perform better than wider (6” nominal) deck boards.

4” nominal deck boards expand and contract less than wider boards

Because there are more gaps between the deck boards, 4” nominal deck boards provide about 44% more top of deck ventilation than 6” nominal decking. Face screws provide more secure fastening than hidden fasteners. This is especially important for low clearance decking.